True Zero-Speed, High Accuracy Gear Tooth Sensor IC 
ATS667LSG
10
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
B
RP
B
OP
B
OP
B
OP(initial)
B
RP(initial)
1
4
2
3
Start Mode
Hysteresis, PO
HYS
Output Signal, V
OUT
If exceed PO
HYS
on high side
If exceed PO
HYS
on low side
IC Position
Relative to Target
Target Magnetic Profile
Differential Signal, V
PROC
Target, Gear
Start Mode Hysteresis
This feature helps to ensure optimal self-calibration by rejecting
electrical noise and low-amplitude target vibration during
initialization. This prevents AGC from calibrating the IC on such
spurious signals. Calibration can be performed using the actual
target features.
A typical scenario is shown in figure 5. The Start Mode Hysteresis,
PO
HYS
 , is a minimum level of the peak-to-peak amplitude of the
internal analog electrical signal, V
PROC
, that must be exceeded
before the ATS667 starts to compute switchpoints.
Figure 5. Operation of Start Mode Hysteresis
" At power-on (position 1), the ATS667 begins sampling V
PROC
.
" At the point where the Start Mode Hysteresis, PO
HYS
 , is exceeded, the device establishes an initial switching threshold, by using the Continuous
Update algorithm. If V
PROC
 is falling through the limit on the low side (position 2), the switchpoint is B
RP
 , and if V
PROC
 is rising through the limit on the
high side (position 4), it is B
OP
. After this point, Start Mode Hysteresis is no longer a consideration. Note that a valid V
PROC
 value exceeding the Start
Mode Hysteresis can be generated either by a legitimate target feature or by excessive vibration.
" In either case, because the switchpoint is immediately passed as soon as it is established, the ATS667 enables switching:
--If on the low side, at B
RP
 (position 2) the output would switch from low to high. However, because output is already high, no output switching occurs.
At the next switchpoint, where B
OP
 is passed (position 3), the output switches from high to low.
  --If on the high side, at B
OP
 (position 4) the output switches from high to low.
As this example demonstrates, initial output switching occurs with the same polarity, regardless of whether the Start Mode Hysteresis is exceeded on the
high side or on the low side.
相关PDF资料
ATS674LSETN-LT-T IC SENSOR GEAR TOOTH 4-SIP
ATS682LSHTN-T IC HALL EFFECT SENSOR 4SIP
ATS685LSHTN-T IC HALL EFFECT GEAR SENSOR 4SIP
BU52001GUL-E2 IC HALL EFFECT SW BIPO VCSP50L1
BU52003GUL-E2 IC HALL EFFECT SW BIPO VCSP50L1
BU52014HFV-TR IC HALL EFFECT SW BIPO HVSOF5
BU52040HFV-TR IC HALL EFFECT BIPO LATCH HVSOF5
D6B-2P SENSR TILT 35-65DEG 1MA SMD GUL
相关代理商/技术参数
ATS668LSMTN-T 功能描述:THREE-WIRE DIFFERENTIAL SPEED SE 制造商:allegro microsystems, llc 系列:* 零件状态:在售 标准包装:1
ATS671LSE 制造商:Allegro MicroSystems LLC 功能描述:
ATS671LSE-T 制造商:Allegro MicroSystems LLC 功能描述:
ATS672LSB 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Self-Calibrating Gear Tooth Sensor with 9-Bit Signal Capture
ATS672LSB_03 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Self-Calibrating Gear Tooth Sensor with 9-Bit Signal Capture
ATS672LSB-HN 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Self-Calibrating TPO Gear-Tooth Sensor with 9-Bit Signal Capture
ATS672LSB-HT 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Self-Calibrating TPO Gear-Tooth Sensor with 9-Bit Signal Capture
ATS672LSB-LN 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Self-Calibrating TPO Gear-Tooth Sensor with 9-Bit Signal Capture